how to make a round wooden hot tub How to Build Your Own Wood Bath

by:ALPHA     2019-06-15

















The wooden bathroom is a great addition to a country historic residence or a remote cottage as it maintains the pioneering spirit of this dwelling.It also provides you with an eco-friendly way to stay clean as it uses renewable resources.Can use some wooden bathtubs that are very easy to buildto-Obtained materials such as birch plywood, plastic tubes, epoxy and screws.This will be a wooden bathtub with a drain pipe 3 feet wide and 6 feet long.By connecting 2 of 1 feet long 2-build a rectangle 3 feet high and 1 feet wideby-Two ends of 4S 3 feet long 2-2by-4s.Use the 3-The inch deck screws that connect these together.Build the second 1 feet high by attaching two 3 feet long 2-1 feet wide rectanglesby-4S two other 2-3 feet long-by-4s.Use 3-as before-The inch deck screws that connect these together.Measuring the middle of 6 feet long 2-using tape measureby-4s.Then use a pencil, 2-in these 6 feet-long-by-4s.6 feet long 2 Buckle 2-by-4S together among themBy placing a 1 feet long 2-by-4 at this point, connect 2-6 feet long-by-4S to 2-1 feet long-by-4 at the midpoint of the 6 feet Mark 2-by-4s.Use the 3-Do this with inch deck screws.This will create a long, short I-shaped piece of wood at the top and bottom.2-6 feet long-by-4S in the middle of them together): Due to 1 feet months-by-4 at this point, connect 2-6 feet long-by-4 \ s to the end of 1 feet long 2-by-4 at the midpoint of the 6 feet Mark 2-by-4\'s.Do this using 3 inch of the deck screws.This will create a second I-shaped block of wood with a long upper and lower arm and a short center block.By connecting a rectangle 6 feet tall and 3 feet wide to the ends of two 1 feet long I-shaped pieces, a box 1 feet long and 3 feet wide and 6 feet tall is constructed.Use the 3-To do this, inch deck screws again.This rectangular box will be a stand for a wooden bathtub.Apply polyurethane resin to the entire rectangular box holder of the bathtub.This will make it waterproof and help it last for a long time.3 feet wide, 6 feet long, 1-Inch thick birch plywood at the top of the bathtub holder to make it flat and completely cover the top of the holder.Then connect the Part 3 feet wide and 6 feet long to the top of the bathtub bracket by drilling 2-1-inch deck screwsBirch plywood and tub holder in inches thick.This is the bottom of the tub.By connection 3 feet wide of In addition two 6 feet long of 1-3 feet wide of 3 feet long of 6 feet high rectangular opening boxBirch plywood in inches thick, forming two 3-feet square, 1-Inch thick birch plywood forming the end of the box.Use the 2-The inch deck screws that connect these together.This is a rectangular bathtub.Place the open rectangular bathtub box 3 feet wide and 6 feet long and 3 feet high on the top of the bathtub holder, so that the top of the cover of the holder completely covers the bottom of the rectangular bathtub box.Connect the rectangular tub box to the top of the tub holder by placing the 1 inch L holder on the inside bottom of the rectangular tub box and driving 1-Inch deck screws go through the top of the L bracket and into the side of the rectangular tub box.Then drive 1-Inch deck screws go through the bottom of the L bracket and into the bottom of the tub.The bathtub is now assembled and needs to be waterproof.Apply polyurethane resin inside and outside the entire bath.This will make the tub waterproof and keep the tub going for a long time.Slide the bathtub into the position above the bathtub drain hole, which is already on the floor of any bathroom where you install the bathtub.Also, the tub needs to be under the tub faucet, which has come out from the wall of any bathroom where you install the tub.Drill a -3-inch diameter holeThe inch round cut drill bit at the bottom of the bathtub, and the end of the bathtub is the bathtub drain hole on the bathroom floor.This will form a drain hole in the bathtub itself.Suitable for 2 feet long, 3-The inch diameter plastic pipe passes through the drain hole of the bathtub and enters the drain hole of the bathtub on the floor of the bathroom.The end of the glue 2 feet long, 3-Fix the inch diameter plastic pipe in the floor drain hole in place with waterproof glue.Then glue the end of 2 feet long, 3-The inch diameter plastic pipe in the drain hole of the bathtub itself is in place with waterproof glue.This is the drain from the bathtub.Place the 3-After the glue on the plastic pipe drain is dry, the inch diameter plug enters the drain hole of the bathtub.The bathtub is now complete and ready to use.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...